Directions

READ THIS INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE USING THE PRODUCT. KEEP THIS DOCUMENT IN THE FABRIC STORAGE BAG WITH THE SEAT AS A REFERENCE GUIDE.

Product Description:     

FlyeBaby is a portable, hammock type seat that can be used on an airplane ONLY during the cruise portion of the flight. It can also attach to most dining room chairs to serve as a high chair.

BEFORE USING THIS PRODUCT, READ THE FOLLOWING WARNINGS:

• Keep packaging away from children.
• FlyeBaby is not an approved safety device.
• FlyeBaby should only be used according to the enclosed instructions.
• To prevent serious injury or death from falls or sliding out, always secure child in harness straps and make sure all straps are securely fastened as illustrated and listed in the instructions.
• Never leave a child unattended while they are in the FlyeBaby seat.
• Inspect the fabric, seams, strapping and buckles before every use and especially after washing.
• FlyeBaby is not a toy.
• Not recommended for children that are restless or for children that will try to escape.
• Do not use the seat if the child has any physical impairments or limitations.
• FlyeBaby is not designed to be used in vehicles.

Airplane use: Maximum Weight 25 lbs/Maximum Height: Top of child’s head should not exceed the Maximum Head Height line printed on the front of the FlyeBaby seat.

When using FlyeBaby, consideration should be made for the child’s development, strength and temperament.

The height requirement listed above must be followed, if the child’s head exceeds the Maximum Height line, then physical contact could occur with the seat located directly in front of the child’s head resulting in injury or death.

The child cannot be in the seat during taxi, take-off or landing. The seat should also not be used as a safety device during turbulence. If turbulence is experienced, the child must be removed from the seat immediately. If not, serious head injury or death could result.

Highchair use: Maximum weight is 25 lbs

• FlyeBaby should only be used for children that can hold their head up and sit up unassisted.
• FlyeBaby will not work on all chair models.
• If the FlyeBaby seat does not fit securely to the chair when following the instructions; DO NOT USE IT.
• Never allow the child to push against a table as the chair could tip over causing injury or death.
• Never allow the child to stand while in the seat as it could result in injury or death.
• Not to be used on chairs that have wheels or on chairs on an uneven surface.

FAILURE TO CONSIDER THE ABOVE WARNINGS AND FAILURE TO FOLLOW THE ENCLOSED INSTRUCTIONS COULD RESULT IN INJURIES OR DEATH OF A CHILD.

CARE INSTRUCTIONS:

Cold wash separately, gentle cycle, no bleach, lay flat to dry. After washing and before using inspect the fabric, seams, strapping and buckles. DO NOT USE the FlyeBaby seat if any damage, fraying or wear occurs.

CUSTOMER SERVICE:

SCS Direct, Inc. number one goal is complete product satisfaction. Should a problem occur please contact customer service at 203-870-4867 and we will resolve the issue. Comments and feedback always welcome and appreciated.

Figure 1.1

Figure 1.2

Figure 1.3

Figure 1.4

[wc_divider style="solid" line="single" margin_top="" margin_bottom=""]

Figure 2.1

Figure 2.2

AIRPLANE USE INSTRUCTIONS:

Maximum weight 25 lbs. Maximum height; see Maximum Head Height Marker on front of FlyeBaby seat. Baby’s head should not exceed this line. FOR IN-FLIGHT USE ONLY. Not to be used during taxi, take-off, landing or turbulence.

STEP 1: Unfold FlyeBaby seat, position it over your knees, harness side down with the top of the seat in the direction of your chest. Release the tray table, secure and fold the top of the FlyeBaby seat over the top of the tray table (See Figure 2.1 on page

2). The center of the circle should fit over the notch on the top of the tray table where the latch will secure the tray when it is in the upright position.

STEP 2: Secure the two vertical straps around the tray table by lacing the straps through the vertical loops (See Figure 2.2). Match the same color tabs on the straps and loops to ensure the set up is correct. (See Figure 1.4 on page 1)

STEP 3: Secure the two horizontal straps around the tray table by lacing the straps through the horizontal loops (See Figures 2.1 and 2.2 on page 2). Match the same colored tabs on the straps and loops to ensure the set up is correct. (See Figures 1.3 and1.4 on page 1)

STEP 4: Return the tray table to the upright position and secure the latch. If the latch is loose and not secure, the tray table could be damaged or broken and you should NOT USE the FlyeBaby in this airplane seat.)

STEP 5: Buckle the bottom strap around the adult’s waist and adjust for a secure but comfortable fit.

STEP 6: Test the seat to make sure it is secure. (DO NOT use if seat is not secure.) Place baby in the five-point harness (See

Figure 1.2 on page 1), secure buckle, adjust shoulder and side waist straps for a secure fit.

HIGH CHAIR USE INSTRUCTIONS:

Maximum weight 25 lbs. This use should only be used for babies that are able to hold their head up and sit up unassisted.

Never leave a child unattended while they are in FlyeBaby.

THERE ARE TWO WAYS THAT THE FLYEBABY SEAT CAN BE USED ON A DINING ROOM CHAIR AND THE INSTALLATION METHOD THAT WILL WORK DEPENDS ON THE STYLE OF THE DINING ROOM CHAIR. PLEASE READ THE FOLLOWING INSTRUCTIONS BEFORE INSTALLING THE FLYEBABY SEAT ON A DINING ROOM CHAIR. (Please note that FlyeBaby will work on most but not all dining room chair models.)

INSTALLATION FOR TALLER BACK DINING ROOM CHAIRS:

STEP 1: Remove the separate chair strap from the pockets located on the back of the FlyeBaby seat and set aside. Place the FlyeBaby seat on the dining room chair and position it so that the harness is located on the base of the chair, giving room for the baby to sit comfortably. (See Figure 2.2 and 2.3 on Page 2) Secure the bottom strap underneath the base of the dining room seat and tighten.

STEP 2: Remove the long strap from the pockets located on the back of the FlyeBaby seat. Secure the FlyeBaby seat to the back of the dining room chair by buckling the long strap with the male buckle into the female buckle base.

STEP 3: Using the separate strap that you set aside in Step 1, thread the top straps through Vertical Loop 1 and Vertical Loop 2 and secure. Match the same color tabs to ensure correct installation (See Figure 2.3 on page 2).

STEP 4: Secure and tighten Horizontal Strap 1 and Horizontal Strap 2 by threading the straps through the loops on the separate chair strap. Adjust the strap as needed to securely fit the specific dining room chair model.

STEP 5: Test the FlyeBaby seat to make sure it is secure (DO NOT USE if it is not secure). Place the child in the five-point harness (See Figure 1.2 on page 1), secure the buckle, adjust the shoulder straps and side waist straps for a secure fit.

INSTALLATION FOR LOWER BACK DINING ROOM CHAIRS:

STEP 1: Remove the separate chair strap from the pockets located on the back of the FlyeBaby seat and place in the fabric storage bag so that this separate strap is not lost. You will not need this separate strap for this installation. (See Figures 2.2 and 2.3 on Page 2) Place the FlyeBaby seat on the dining room chair and position it so that the harness system is located on the base of the chair, giving room for the baby to sit comfortably. Secure the bottom strap underneath the base of the seat and tighten.

STEP 2: Remove the long strap from the pockets located on the back of the FlyeBaby seat. Secure the FlyeBaby seat to the back of the dining room chair by buckling the long strap with the male buckle into the female buckle base.

STEP 3: Fold the top of the FlyeBaby seat over the top of the dining room chair. The center of the circle cutout should be located at the top of the dining room chair creating a half circle cut out on the front and back of the dining room chair.

STEP 4: Secure Horizontal Strap 1 and Horizontal Strap 2 by threading the straps through Horizontal Loop 1 and Horizontal Loop

2. Match the same color tabs to ensure correct installation. (See Figures 2.1 and 2.2 on page 2) Depending on the style of the dining room chair, you may also secure the two vertical straps by threading the straps through the vertical loops and matching the same color tabs.

(It is not necessary to use the two vertical straps for the dining room chair use if the FlyeBaby seat is secured by the horizontal straps.)

STEP 5: Test the FlyeBaby seat to make sure it is secure (DO NOT USE if it is not secure). Place the child in the five-point harness (See Figure 1.2 on page 1), secure the buckle, adjust the shoulder straps and side waist straps for a secure fit.